What is the low beam headlight bulb size for a 1987 Oldsmobile Cutlass?

The 1987 Oldsmobile Cutlass uses a 9004 bulb for the low beam headlights. We recommend upgrading to LED for better visibility.

What is the high beam headlight bulb size for a 1987 Oldsmobile Cutlass?

The high beam bulb size for the 1987 Oldsmobile Cutlass is 9004.

Why are my 1987 Oldsmobile Cutlass headlights dim?

Dim headlights on a 1987 Oldsmobile Cutlass can be caused by aging halogen bulbs, which lose brightness over time, or oxidation (cloudiness) on the plastic headlight lenses. Upgrading to a 9004 LED conversion kit can provide a significantly brighter and whiter light output.

Which bulb fits the 1987 Oldsmobile Cutlass fog light?

The 1987 Oldsmobile Cutlass typically does not come with factory fog lights in all trim levels. If your vehicle is equipped with them, check the manual as sizes can vary by trim.

Is the 1987 Oldsmobile Cutlass single or dual beam?

The 1987 Oldsmobile Cutlass uses a single bulb (dual filament) headlight system. This means one bulb controls both high and low beams.

Can I install LED bulbs on my 1987 Oldsmobile Cutlass?

Yes, the 1987 Oldsmobile Cutlass comes with standard halogen bulbs from the factory, but they can be upgraded to LED. You will need a 9004 LED conversion kit for the low beams.

Did the 1987 Oldsmobile Cutlass change headlight bulb sizes from the previous year?

Yes — the 1987 Oldsmobile Cutlass uses different bulb sizes than the 1986 model. The 1987 generation introduced this bulb configuration.

Is the 1987 Oldsmobile Cutlass the first or last year to use 9004 bulbs?

The 1987 Oldsmobile Cutlass is the only year in the 1987 generation to use the 9004 bulb for the low beam headlight.

How do I change the headlight on a 1987 Oldsmobile Cutlass?

Turn off the vehicle and open the hood. Locate the headlight assembly from behind, remove the dust cover or retaining clip, disconnect the wiring harness, twist the old 9004 bulb counter-clockwise to remove it, then insert the new bulb and reassemble. The whole process typically takes 10 to 30 minutes per side depending on accessibility.

Are LED headlights legal for a 1987 Oldsmobile Cutlass?

LED bulbs used off-road or in auxiliary lights are legal everywhere. For on-road headlight use, legality varies by state. Many states allow LED retrofits as long as the beam pattern meets DOT standards. For the best legal compliance, choose a DOT-approved 9004 LED kit that is designed as a direct replacement and produces a proper cutoff pattern without excessive glare.

How much does it cost to replace 1987 Oldsmobile Cutlass headlights?

A pair of halogen 9004 bulbs costs $15 to $40, while LED conversion kits run $25 to $60 per pair. If you have a shop do the work, expect an additional $20 to $50 in labor per bulb. Replacing them yourself at home saves the labor cost and usually takes under 30 minutes.

What is the difference between halogen and LED for a 1987 Oldsmobile Cutlass?

Halogen bulbs produce a warm yellow light (around 3200K), last 500 to 1000 hours, and draw more power. LED bulbs emit a brighter white light (5000-6000K), last 25,000+ hours, and use less energy. LED upgrades for the 9004 position are available as direct plug-and-play replacements.

The 1987 Oldsmobile Cutlass has a unique bulb configuration not shared with adjacent model years.

Fitment Guaranteed for 1987 Oldsmobile Cutlass

What Size Bulbs Does a 1987 Oldsmobile Cutlass Use?

Correct headlight, fog light, and tail light bulb sizes. Sourced from OEM catalog data.

Installation Difficulty

Easy (Plug and Play)

Est. Replacement Cost

$15 - $40 (Halogen) / $30+ (LED)

What Lighting System Does the 1987 Oldsmobile Cutlass Have?

Lighting on the 1987 Oldsmobile Cutlass is managed by a total of 11 bulbs, covering everything from primary headlights to signal indicators. It features an extensive lighting system powered by a halogen-based setup where a single 9004 dual-filament bulb handles both low and high beam duties within the same reflector. This model belongs to the mid years of the Cutlass's 1961-1999 production span.

Can You Put LED Bulbs in a 1987 Oldsmobile Cutlass?

Upgrading to LED is one of the most effective ways to modernize your Oldsmobile's appearance and safety profile. Since your Cutlass uses a single 9004 bulb for both high and low beams, ensure your chosen LED kit is "dual-beam" compatible. This allows the LED circuitry to mimic the two-filament design of the original halogen bulb.

1987 Oldsmobile Cutlass Bulb Size Chart

Position	Bulb Size	Shop
Low Beam	9004	Buy 9004 →
Turn Signal Front	1157A	Buy 1157A →
Side Marker	194	Buy 194 →
High Beam	9004	Buy 9004 →
Turn Signal Rear	1157	Buy 1157 →
License Plate	194	Buy 194 →
Tail Light	1157	Buy 1157 →
Parking Light	1157A	Buy 1157A →
Reverse Light	1156	Buy 1156 →
Brake Light	1156	Buy 1156 →
Map Light	906	Buy 906 →

How do the 1987 Oldsmobile Cutlass's bulbs compare to other years?

The 1987 Oldsmobile Cutlass changed bulb sizes from 1986. The previous model year used a different configuration.

The 1997 model switched to a different bulb configuration.

This bulb configuration covers the 1987 model years. ← 1986 1997 →

Finding the best installation guide...

Other Cutlass Years

1999 1998 1997 1986 1985 1984 1983 1982 1981 1980 1978 1977 1976 1975 1974 1973 1971 1970 1969 1968 1967 1966 1965 1964 1963 1962 1961

More from Oldsmobile

442 88 98 Achieva Alero Aurora Bravada Calais

Other Vehicles That Use 9004 Bulbs

2005 Pontiac Montana 2003 Dodge Ram Van 2003 Dodge Wagon 2002 Mercedes-Benz SL-class 2002 Mercedes-Benz SL500 2002 Mercedes-Benz SL600